eXtremeRate Top Bottom Decorative Trim Shell Compatible with ps5 Edge Controller DIY Replacement Front Back Clip Shell, Custom Black Plates Cover Compatible with ps5 Edge Controller

Great fits really well, didn’t really affect the grip .

blown away by this product .. as I huge gamer the rubbers on my pad started to peel off .. pritty piss poor for a £200 controller but this product saves the day and looks amazing now ..real easy to install also 👌🏻

I had to get my Duelsense Edge replaced as the grips (which are made of rubber) started to peel and bubble from being used. A design flaw that they don't use on their normal controllers at a fraction of the cost.This replacement doesn't "quite" reach the edge of where it's placed, but it still looks great and feels better. It's easy to install too.

Fits perfectly and a great replacement for the original grips which start peeling. No idea why Sony uses these grips on a £200 controller

Stock grip on the back was peeling on the edges and bubbling in the middle so needed a replacement, saw reviews and looked good. Installation is a bit finicky but there are videos for installation but the end result is perfect! Would recommend and if I had the option would go back and get the full case instead of just the back and top trim for an all black controller.

Fantastic to have a trim that is a genuine solution for the peeling grips on the PS5 Edge Controller - not cheap but feels decently made, looks good and in my instance possible to make fit correctly after some minimal trimming... sadly only after another clip had snapped despite watching as many installation guides as I could find and reading reviews - I'm mechanically minded and have reasonable experience dismantling and repairing this kind of thing. Unsure if it's worth returning for a replacement as this one fits correctly now even if a bit damaged inside ... but I am curious if the clips that seem to be causing everyone fitment issues, differed in some way from the official trim enough to cause them to bend/crush during the fitting process? Seems likely as refitting the original trim had no such issue with gaps or crushing the clips in that place after removing and refitting a number of times.

Fit perfectly for me, wish this had came out from the release of the controller😅👌.

Ok, so I have 2 Edge Controllers. I’m very OCD about my things and looks after them. I have both my Edge controllers in covers/ cases because I want to keep them protected from wear, marks, discolouring etc.I recently read about the issue with the rubber grips peeling on the Edge controllers and became concerned because it seems to be a widespread issue. The rubber grips blister at first and then start to peel away. Not good for a £200 controller and also a massive design blunder by Sony.I haven’t had this issue, I think mainly because I am very careful when I handle my controllers and the fact they are in covers which help combat friction between your hands and the rubber grip on the controller when using it.The last thing I wanted was for the rubber on my Edge controllers peeling away. Sony do not appear to sell replacement back plates. Also, the back plates on the Edge controller had the data stamp on it, with serial number etc.So if the original back plate is ruined by peeling rubber, you’re pretty much screwed.You won’t be able to get a replacement with your serial number etc on it.If you send the controller back to Sony for repair, they may just fit another back plate to it that doesn’t have your original data stamped on it. There is a chance they might make a new back plate for you and also print all your controllers original data on it, but I don’t think they’ll go to those lengths.My friend had just sent his back to Sony for peeling rubber. He will receive it back any day. I asked him to take pics of the original back plate so we can see what he receives back from Sony, so I will soon see what Sony does when “repairing” this issue!Anyway, the solution for me was to buy replacement back plates and store my originals in the controller packaging.It’s not great that we have to do this and I’m sure Sony will be revising the design of the Edge grips in due course. They are having ALOT of Edge’s sent back to them so they will have to address this.These extreme rate plates are decent enough.The finish is good. I got 1 blue set and 1 red set.Disappointed to see that the insides of the plates were not painted. Makes them look cheap and unfinished. Yes, you won’t see the insides but for £30+, they should have painted all of it.The fitment is 90%.There are two small gaps on either side on the back of the controller. It’s minor but the gaps are there.I have my controllers in covers so I’m not overly bothered. The main aim for me was to preserve the original Edge back plates.I didn’t swap out the release switch rail. Honestly, there’s no need. Just keep the original in place and keep the extreme rate rail stored.I’m actually surprised extreme rate went to the trouble of making a replacement rail JUST to have a matching colour on the very very small slider switch that releases the front plate.I mean, I’m all about the OCD, but even I am happy keeping the original release switch rail in place and unmolested. I also think that the material that Sony use will be superior to the extreme rate rail. No offence.All in all, decent fitment and nice finishes.But could be better for the price.One more thing, to you, extreme rate…You really need to package the plates better.The boxes are lovely and strong.But you literally put both plates in the same plastic bag, unprotected. This means that they are free to rub against each other and scratch each other.There are 2 small scratches on my blue set.This really annoyed me because it could have been avoided if you had just put them in little sleeves before packing them.Because of my reason for buying these and he fact I have covers on my controllers, I am willing to let it go.But if I didn’t use covers, I would be returning the blue set for replacements.Just a friendly heads up!